View RM186-SM_8762650.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

a datasheet lora/bluetooth low energy (ble) module part numbers: rm186 and rm191 version 1. 4
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 2 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 r evision h istory version date notes approver 1.0 19 may 2016 initial version jonathan kaye 1.1 20 may 2016 updated sig section with url to listing jonathan kaye 1.2 11 aug 2016 changed hardware integration guide to datasheet sue white 1.3 2 nov 2016 updated section numbers sue white 1.4 01 feb 2017 updated to include ble peripheral mode jonathan kaye
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 3 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 c ontents 1 overview and key features ................................ ................................ ................................ ................................ 5 1.1 features and benefits ................................ ................................ ................................ ................................ . 5 1.2 application areas ................................ ................................ ................................ ................................ ........ 5 2 specif ications ................................ ................................ ................................ ................................ ...................... 6 3 hardware specifications ................................ ................................ ................................ ................................ ..... 9 3.1 block diagram and pin - out ................................ ................................ ................................ ......................... 9 3.2 pin definitions ................................ ................................ ................................ ................................ ......... 10 3.3 elec trical specifications ................................ ................................ ................................ ........................... 12 3.3.1 absolute maximum ratings ................................ ................................ ................................ ............. 12 3.3.2 recommended operating parameters ................................ ................................ ............................ 12 3.3.3 nautorun pin and operating modes ................................ ................................ .............................. 14 3.3.4 lora output power and current consumption vs vcc ................................ ................................ .... 14 3.3.5 lora receive sensitivity vs data rate ................................ ................................ ............................. 16 3.3.6 ble power consumption ................................ ................................ ................................ ................. 16 4 functional description ................................ ................................ ................................ ................................ ..... 19 4.1 power management (includes brown - out and power on reset) ................................ ............................. 19 4.2 clocks and timers ................................ ................................ ................................ ................................ .... 20 4.2.1 clocks ................................ ................................ ................................ ................................ ............... 20 4.2.2 timers ................................ ................................ ................................ ................................ .............. 20 4.3 rf ................................ ................................ ................................ ................................ ............................. 20 4.4 uart interface ................................ ................................ ................................ ................................ ......... 20 4.5 spi bus ................................ ................................ ................................ ................................ ..................... 21 4.6 i2c interface ................................ ................................ ................................ ................................ ............ 22 4.7 general purpose i/o, adc and pwm/freq ................................ ................................ ............................ 22 4.7.1 gpio ................................ ................................ ................................ ................................ ................. 22 4.7.2 adc ................................ ................................ ................................ ................................ .................. 22 4.7.3 pwm and freq signal output on up to two sio pins ................................ ................................ .... 23 4.8 nreset pin ................................ ................................ ................................ ................................ ............... 23 4.9 nautorun pin ................................ ................................ ................................ ................................ .......... 23 two - wire swd programming/debug interface ................................ ................................ ................................ .. 23 4.10 rm1xx on - board chip antenna characteristics ................................ ................................ ........................ 24 5 hardware integration suggestions ................................ ................................ ................................ .................. 24
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 4 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 5.1 circuit ................................ ................................ ................................ ................................ ....................... 24 5.2 pcb layout on host pcb C general ................................ ................................ ................................ .......... 26 5.2.1 ble chip antenna keep - out on host pcb ................................ ................................ ........................ 26 5.2.2 antenna keep - out and proximity to metal or plastic ................................ ................................ ...... 27 5.3 lora external antenna integration with rm1xx ................................ ................................ ..................... 28 6 mechanical details ................................ ................................ ................................ ................................ .......... 28 6.1 rm1xx mechanical details ................................ ................................ ................................ ...................... 28 6.2 host pcb land pattern and antenna keep - out for rm1xx ................................ ................................ ...... 29 7 application note for surface mount modules ................................ ................................ ................................ 30 7.1 introduction ................................ ................................ ................................ ................................ ............. 30 shipping ................................ ................................ ................................ ................................ ............................... 30 7.2 reflow parameters ................................ ................................ ................................ ................................ .. 31 8 fcc and ic regulatory statements ................................ ................................ ................................ .................. 32 8.1 power exposure information ................................ ................................ ................................ ................... 33 oem responsibilities ................................ ................................ ................................ ................................ ........... 33 9 ce regulatory ................................ ................................ ................................ ................................ .................. 35 9.1 antenna information ................................ ................................ ................................ ............................... 36 10 eu declarations of conformity ................................ ................................ ................................ .................... 37 10.1 rm186 - sm ................................ ................................ ................................ ................................ ............... 37 11 ordering information ................................ ................................ ................................ ................................ .. 38 11.1 general comments ................................ ................................ ................................ ................................ .. 38 12 blu etooth sig qualification ................................ ................................ ................................ ......................... 38 12.1 overview ................................ ................................ ................................ ................................ .................. 38 12.2 additional assistance ................................ ................................ ................................ ............................... 39
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 5 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 1 o verview and k ey f eatures this datasheet describes both the rm186 (868 mhz band for eu) and rm191 (915 mhz band for us) . the differences are outlined in the radio s pecifications. every rm1xx series module is designed to enable oems to add a long range lora radio link and either c entral or peripheral mode bluetooth low energy (ble) to small, portable, power - conscious devices. the rm1xx modules are enabled with lairds smart basic , a n event - driven programming language that enables oems to make their product development quicker and simpler, significantly reducing time to market. s mar t basic enables customers to develop a complete embedded application inside the compact rm1xx hardware, c onnecting to a wide array of external sensors via its i2c, spi, uart, adc , or gpio interfaces. based on the world - leading nordic semiconductor nrf51822 (ble) and semtech sx1272 (lora) chipset s , the rm1xx modules provide ultra - low power consumption with out standing wireless range using the lora radio link and local ble connections via three dbm of tra nsmit power. this document should be read in conjunction with the smart basic user manual. note: this information in this document is subject to change. please contact laird to obtain the most recent version of this document C http://ews - support.lairdtech.com . 1.1 features and b enefits 1.2 application areas ? bluetooth v4.0 C central or peripheral mode ? on - board ble c hip a ntenna ? u .fl for external lora antenna ? smart basic programming language ? bluetooth sig listed ? compact f ootprint ? long r ange C lora range up to 15 km ? ble programmable tx power +3 dbm to - 20 dbm ? ble tx whisper mode ( - 30 dbm, - 55 dbm) ? ble rx sensitivity: - 91 dbm ? ultra - low power consumption ? ble tx: 1 2.7 ma peak (at + 3 dbm @vcc=3.3v ) ( see note 4 in the power consumption section) ? ble rx: 11.9 ma peak ( @vcc=3.3v see note 4 in the power consumption section) ? standby doze: 4.2 ua (typical) ? deep sleep: 750 na ( see note 4 in the power consumption section) ? uart, gpio, adc, pwm freq output, timers, i2c, and spi interfaces ? fast time - to - m arket ? fcc /ic (rm191 - sm) , ce (rm186 - sm) ? no external components required ? public or private n etworks ? irrigation/ agriculture ? parking ? ligh ting ? asset t racking ? tank m onitoring ? smart home C smoke alarms, heating, ? access c ontrol C security ? industrial automation C f actory ? any long range, bat tery powered sensor application
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 6 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 2 s pecifications table 1 : specifications categories feature implementation lora wireless specification lora? lorawan 1.01 (end device) frequency 902 - 928mhz rm191 865 - 870 mhz rm186 maximum transmit power setting 1 5.5 dbm rm191 1 3.5 dbm rm186 minimum transmit power setting 1.5 dbm receive sensitivity - 126 dbm - 134 dbm rm191 (b w 500 khz s f 12) rm186 (bw 125khz sf 12) range up to 15 km in free space raw data rates (over the air) 250 bps C 50 kbps rm186 980 bps C 21.9kbps rm191 ble wireless specification bluetooth? (ble) v4.0 C central or peripheral mode frequency 2.402 - 2.480 ghz maximum transmit power setting 3 dbm (into - 1.5 dbi chip antenna) minimum transmit power setting - 20 dbm (in four db steps) with smart basic command - 16 dbm - 12 dbm - 8 dbm - 4 dbm 0 dbm tx whisper mode 1 transmit power - 30 dbm (min . ) with smart basic command tx whisper mode 2 transmit power - 55 dbm (min . ) with smart basic command receive sensitivity (0.1% ber) - 91 dbm typical link budget 95 db (@ 1 mbps) range up to 100 m in free space tx whisper modes range reduction feature with tx whisper modes with smart basic command. range (tx whisper mode 2) <~30 cm raw data rates 1 mbps (over the air) host interface and peripherals total 14 x multifunction i/o lines uart tx, rx, cts, rts dcd, ri, dtr, dsr, cts, rts (note 1) default 115200, n, 8, 1 from 1,200 to 460800 bps gpio up to 14 with configurable i/o direction, o/p drive strength (standard 0.5 ma or high 5 ma), pull - up /pull - down
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 7 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 categories feature implementation adc four 10 - bit channels (including adc reference) 10 bit resolution 1.2 v internal reference 1/1, 2/3, 1/3 pre - scaling pwm or freq output pwm or freq outpu t on up to two gpio output pins: pwm output duty cycle 0% - 100% pwm output frequency up to 500 khz (note 7) freq output frequency 0 mhz - 4 mhz (50% duty cycle) i2c one i2c interface (up to 400 kbps) (note 2) spi one spi master interface (up to 4 mbps) (note 3) ble services services supported gatt client and capabilities fw upgrade smart basic runtime engine fw upgrade (1) via uart (2) via 2 - wire swd programming/debug interface programmability smart basic on - board programming language similar to basic. smart basic application download (1) via uart. (2) via 2 - wire swd programming/debug interface control protocols any user defined via smar tbasic operating modes self - contained run mode selected by nautorun pin status: nautorun = low (0v): then runs $autorun$ ( smart basic application script) if it exists. interactive / development mode nautorun = high (vcc): then runs via at+run (and file name of smart basic application script). supply voltage supply (vcc) 2.1 v C 3.5 v int ernal dcdc converter (note 5) 1.8 v C 2.1 v internal ldo dcdc switched on if vcc >2.1v at power - up ble power consumption active modes peak c urrent (for max tx pwr 3 dbm) connected mode (vcc=3.3v) 1 2 . 7 ma peak tx 11 .9 ma peak rx active modes peak c urrent ( for tx whisper mode2 pwr - 55 dbm) connected mode (vcc=3.3v) 5 ma peak tx 11.9 ma peak rx active modes average c urrent depends on many factors. s ee power consumption . ultra - low power m odes standby doze deep sleep 4.2 ua typical (note 6) 750 na (note 6) antenna options ble (internal) chip a ntenna on - board ceramic chip monopole antenna - 1.5 dbi lora (external) dipole antenna with u.fl (ipex) connector up to 2 dbi physical dimensions 25.4 mm x 25.4 mm x 3.1 mm weight 3 grams environmental operating - 40 ?c to + 8 5 ?c (vcc 1.8v C 3.5 v ) storage - 40 ?c to +85 ?c
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 8 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 categories feature implementation miscellaneous lead free lead - free and rohs compliant warranty 1 - year warranty development tools development kit development kit dvk - rm1xx and free software tools approvals bluetooth? sig listed C declaration id fcc / ic / ce rm191 - sm: fcc/ic, rm186 - sm: ce note 1: dsr, dtr, ri, and dcd can be implemented in the smart basic application. note 2: with i2c interface selected, pull - up resistors on i2c sda and i2c scl must be connected externally as per i2c standard. note 3: spi interface (master) consists of spi mosi, spi miso and spi clk. s pi cs is created by customer using any spare sio pin within their smart basic application script allowing multi - dropping. note 4: rm1xx module comes loaded with smart basic runtime engine fw, but does not come loaded with any smart basic application script (as that is dependent on customer end application or use). laird provides many sample smart basic application scripts covering the services listed. additional applications being added every quarter. note 5: laird suggests using vcc of 3.3v +/ - 5% (3.13v - 3.46v) for maximum lora output power. warning: above 3.5v, the lora transmitter will be disabled to maintain regulatory compliance note 6: deep sleep current < 750 na (typi cal). standby doze curren t 4.2ua (typical). note 7: pwm output signal has a frequency and duty cycle property. pwm output is generated using 32 - bit hardware timers. the timers are clocked by a 1mhz (1us period) clock source. trade - off pwm output frequency with resolution. for example: pwm output frequency of 500khz (2us) results in resolution of 1:2 pwm output frequency of 100khz (10us) results in resolution of 1:10 pwm output frequency of 10khz (100us) results in resolution of 1:100 pwm output frequency of 1khz(1000us) results in resolution of 1:1000 refer to the smart basic user guide for details.
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 9 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 3 h ardware s pecifications 3.1 block diagram and pin - out figure 1 : functional hw and sw block d iagram for rm1xx series smart basic module s figure 2 : rm186/ rm191 module pin - out (top view)
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 10 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 3.2 pin definitions table 2 : pin definitions pin # pin name default function alt. funct. default direction note14 pull - up / pull - down note14 notes comment 1 gnd - - - - - - 2 sio_ 21 dio uart tx out set high in fw 1,2,4, 6,7 uartclose() selects dio functionality and uartopen() selects uart comms behaviour 3 sio_22 dio uart rx in pull - up 1,2,4,6,7 4 sio_2 3 dio uart rts out set low in fw 1,2,4,6,7 5 sio_ 24 dio uart cts in pull - down 1,2,4,6,7 6 sio_ 25 nautorun /dio dio in none in only laird devkit, uart_dsr via j10, j12 7 sio_ 28 dio - in pull - up 13,1,2,6 laird devkit: j6 8 gnd - - - - - 9 sio_ 29 dio i2c scl in pull - up 1,2, 6,11 i2copen() in smart basic selects i2c function 10 sio_30 dio i2c sda in pull - up 1,2,6,11 11 gnd 12 vcc_ble - - - - - vcc for ble radio 13 vcc_lora - - - - - vcc for lora radio 14 gnd - - - - - 15 sio_ 00 dio spi clk in pull - up 1,2,6 ,11 spiopen() in smart basic selects spi function, mosi and clk will be outputs when in spi master mode. see note 11 16 sio_1 7 dio spi miso in pull - up 1,2, 6,11 17 sio_03/ain dio/ain spi mosi in pull - up 1,2,3,4,5,6,11 18 sio_ 04/ain dio ain in pull - up 1,2 ,3,4,5,6,11 laird devkit: spi slave select 19 sio_ 05/ain dio ain in pull - up 1,2,3,4,5,6,11 laird devkit: button2 or ana temp sensor via j7 20 sio_ 06/ain dio ain in pull - up 1,2,3,4,5 ,6,11 laird devkit: led5 or arduino a0 via j8 21 gnd 22 nreset in 9,10 system reset (active low) 23 nc 9 do not connect 24 gnd
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 11 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 note 1: secondary function is selectable in smart basic application. note 2: dio = digital input or output. i/o voltage level tracks vcc. note 3: ain = analog input note 4: dio or ain functionality is selected using the gpiosetfunc() function in smart basic. note 5: ain configuration selected using gpiosetfunc() function. note 6: i2c, uart, spi controlled by xxxopen() functions in smart basic. note 7: sio_21 to sio_24 are dio by default when $autorun$ app runs on power up. note 8: n/a note 9: hidden 2 - wire swd programming/debug interface , pin22 (swdio) and pin23 (swdclk). used for upgrading smart basic runtime engine fw with j - link programmer. using this hidden 2 - wire swd programming/debug interface on customers host pcb requires header connector s a mtec ftsh - 105 - 01 - l - dv, refer to section 2 - wire swd programming/debug interface for details. note 10: pull the nreset pin (pin 22) low for min imum 100 ms to reset the module . note11: spi cs is created by customer using any spare sio pin within their smart basic application script allowing multi - dropping. note12: n/a note13: n/a note14: smart basic runtime engine has dio (default function) input pins, have by default pull - up enabled. this was done to avoid floating inputs (which can also cause current consumption in low power modes (e.g. standby doze) to drift with time. in any case customer can disable the pul - up through their s mart basic application. all the sio pins (with a default function of dio are inputs C apart from sio_21 and sio_23, which are outputs): - sio_21 (alternative function uart_ tx ) is an output, set high (in fw). - sio_23 (alternative function uart_rts) is an output, set low (in fw). - sio_22 (alternative function uart_rx) is an input, set with internal pull - up (in fw). - sio_24 (alternative function uart_cts) is an input, set with internal pull - down (in fw). the rm1xx module is delivered with the integrated smart basic runtime engine fw loaded (but no onboard smart basic application script) . b ecause of this, it starts up in at command mode by default. at reset, all sio lines are configured as the defaults shown above. sio lines can be configur ed through the smart basic a pplication script to be either inputs or outputs with pull - ups or pull - downs. w hen an alternative sio function is selected (such as i2c or spi ), the firmware does not allow
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 12 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 the setup of internal pull - up/pull - down. therefore , when i2c interface is selected, pull - up resistors on i2c sda and i2c scl must be connected externally as per i2c standard. uart_rx, uart_tx, uart_cts are vcc logic level s (if vcc is 3.3 v, i.e. sio pin i/o levels track vcc). for example, when rx and tx are idl e , they sit at 3.3 v (if vcc is 3.3 v). conversely , handshaking pins cts and rts at 0 v are treated as assertion s . pin 6 (nautorun) is an input, with active low logic. in the dev elopment kit (dvk - rm1xx - sm) it is connected so that the state is driven by the hosts dtr output line. the nautorun pin must be externally held high or low to select between the following two operating modes: ? self - contained run mode (nautorun pin held at 0 v). ? interactive / develop ment mode (nautorun pin held at vcc). smart basic runtime engine firmware checks for the status of naut orun during power - up or reset. if it is low and if there is a smart basic a pplication script named $autorun$ , then the smart basic runtime engine fw ex ecute s the application script automatically; hence the name s elf - contained r un m ode . 3.3 electrical specifications 3.3.1 absolute maximum ratings absolute maximum ratings for supply voltage and voltages on digital and analog ue pins of the m odule are listed below; ex ceeding these values causes permanent damage ( table 3 ) . table 3 : maximum current ratings parameter minimum maximum unit voltage at vcc _ble and vcc_lora pin - 0.3 +3. 6 ( note 1 ) v voltage at gnd pin 0 v voltage at sio pin - 0.3 vcc+0.3 v storage temperature - 40 +85 o c note 1: absolute max rating for vcc pin (max) is 3.6v , however we recommend 3.3v +/ - 5% as the spec for maximum vcc. the lora transmitter s huts down if the voltage exceeds 3.5v . 3.3.2 recommended operating parameters table 4 : power supply operating parameters parameter minimum typical maximum unit vcc 1 1.8 3 .3 3.5 v vcc maximum ripple or noise 2 10 mv operating temperature range - 40 - +85 oc note 1: internal dcdc is used if vcc >2.1 v on power - up; otherwise internal ldo is used . if supply voltage is greater than 3.5v, the lora transmitter will be disabled. note 2: the maximum vcc ripple or noise (at any frequency) that does not disturb the radio.
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 13 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 table 5 : signal levels for interface, sio parameter minimum typical maximum unit vih input high voltage 0.7 v cc vcc v vil input low voltage vss 0.3 v voh output high voltage (std. drive, 0.5ma) (high - drive, 5ma) ( note 1 ) v cc - 0.3 v cc - 0.3 vcc vcc v v vol output low voltage (std. drive, 0.5ma) (high - drive, 5ma) ( note 1 ) vss vss 0.3 0.3 v v pull up resistance 11 13 16 k ? pull down resistance 11 13 16 k? note 1: maximum number of pins with 5ma high drive is three. table 6 : sio pin alternative function ain (adc) specification parameter minimum typical maximum unit adc internal reference voltage - 1.5% 1.2 v +1.5% % adc pin input internal selectable scaling 1/1, 1/3, 2/3 scaling adc input pin (ain) voltage maximum without damaging adc w.r.t vcc prescaling 3.3 v 1/1 3.3 v 2/3 3.3 v 1/3 1.8 v 1/1 1.8 v 2/3 1.8 v 1/3 2.4 3.6 3.6 2.1 2.1 2.1 v v v v v v adc input pin (ain) voltage maximum without saturating adc (with 1.2v internal reference) 1 1/1 prescaling 2/3 prescaling 1/3 prescaling 1.2 1.8 3.6 v v v time required to convert single sample in 10bit mode 9bit mode 2 8 bit mode 2 68 36 20 us us us adc input impedance (during operation) 3
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 14 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 note 1: stay within internal 1.2 v reference voltage with given prescaling on ain pin and do not violate adc maximum input voltage (for damage) for a given vcc, e.g. if vcc is 1.8 v can only expose ain pin to 2.1 v (vcc+0.3). note 2: currently, the smart basic runtime engine firmware only allows 10 - bit mode. note 3: adc input impedance is estimated mean impeda nce of the adc (ain) pins. the tolerance is +/ - 20%. the adc is highly sensitive to the impedance of the source. the adc (ain) input impedance is 200k - 600k depending on your adc gain (pre - scaling) setting. normally, when not sampling, the adc (ain) impedanc e will have very high value and can consider it to be an open circuit. the moment adc is sampling, adc (ain) impedance is 200k - 600k. 3.3.3 nautorun pin and operating modes operating modes (refer to the smart basic manual for details): ? self - contained mode ? interact ive/development mode table 7 : nautorun pin signal name pin # i/o comments nautorun (sio_ 25 ) 6 i input with active low logic. operating mode selected by nautorun pin status: if low (0v), runs $autorun$ if it exists; if high (vcc) , run s via at+run (and file name of application ) . pin 40 (nautorun) is an input, with active low logic. in the development board (dvk - rm1xx ) it is connected so that the state is driven by the hosts dtr output line. nautorun pin needs to be externally held high or low to select between the two rm1xx operating modes: ? self - contained run mode (nautorun pin held at 0v). ? interactive/development mode (nautorun pin held at vcc) smart basic runtime engine firmware chec ks for the status of nautorun during power - up or r eset. if it is low and if there is a smart basic a pplication named $autorun$ then the smart basic runtime engine execute s the application automatically ; hence the name self - contained run mode . 3.3.4 lora output po wer and current consumption vs vcc to maximize output power, the best choice for module vcc is 3.3v +/ - 5% (which results in a vcc range of 3.14v to 3.47v). t he d ata in table 8 was taken at 25 o c with uart on and a ll other peripherals turned o f f . it shows how the output power and transmitter current consumption falls off as a function of vcc. table 8 : power consumption and output p ower vs vcc rm186 rm191 vcc [v] tx current [ma] rx current [ma] pout [dbm] tx current [ma] rx current [ma] pout [dbm] 3.5 31.4 12.7 13.8 45.7 15.3 15.2 3.3 30.9 12.6 13.5 43.3 15.0 14.9 3.0 29.5 12.3 13.0 39.8 15.1 14.3
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 15 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 rm186 rm191 2.7 27.9 12.2 12.2 36.3 14.8 13.4 1.8 19.4 11.8 6.5 24.5 14.4 8.5 3.3.4.1 typical lora current waveforms for tx/rx cycle the plots below ( figure 3 and figure 4 ) depict a typical transmit/receive cycle when sending a lora packet to th e gateway. the plots were made using a shunt current monitor and the voltage levels have been translated to curr ents. the current plots show a transmitted packet, the first receive window ( one second later), followed by the second receive window ( one secon d following the first receive window ) . the currents represented are the total module current (the sum of vcc_ble and vcc_lora pins). figure 3 : typical rm186 lora transmit/receive cycle (full tx power, vcc=3.3v, @25 c figure 4 : typical lora transmit/receive c ycle (full tx power, vcc=3.3v, @25?c)
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 16 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 3.3.5 lora receive sensitivity vs data rate table 9 tabulates typical lora receive sensitivity as a function of the lora data rate . the data rate is determined by the combination of bandwidth and spreading factor of the incoming lora signal. the data rates in the table are the lorawan data rates used by the gateway when transmitting to the end device. table 9 : receive sensitivity vs lora data rate dr bit rate [bits/s] bw [khz] sf rx sensitivity [dbm] rm191 8 980 500 12 - 126 9 1760 500 11 - 125 10 3900 500 10 - 122 11 7000 500 9 - 119 12 12500 500 8 - 116 13 21900 500 7 - 113 rm186 0 250 125 12 - 134 1 440 125 11 - 132 2 980 125 10 - 130 3 1760 125 9 - 127 4 3125 125 8 - 124 5 5470 125 7 - 121 6 11000 250 7 - 119 note the following: ? dr = lora wan d ata rate ? bit r ate is the effective over the air bit rate ? bw is the bandwidth of the incoming lora transmission ? sf is the spreading factor of the incoming lora transmission 3.3.6 ble power consumption data taken at vcc 3.3v (see note 1 following table 10 ) and 25 o c. table 10 : power consumption parameter min typical max unit active m ode peak current C ( note 1 ) (connection) tx only run peak current @txpwr= + 3 dbm tx only run peak current @t pwr= 0 dbm tx only run peak current @txpwr= - 4 dbm tx only run peak current @txpwr= - 8 dbm tx only run peak current @txpwr= - 12 dbm tx only run peak current @txpwr= - 16 dbm t x only run peak current @txpwr= - 20 dbm 12.7 8.4 7.1 6.9 6.4 6.1 5.5 ma ma ma ma ma ma ma
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 17 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 parameter min typical max unit tx whisper m ode 1 tx only run peak current @txpwr= - 30 dbm tx whisper m ode 2 tx only run peak current @txpwr= - 55 dbm 5.4 5.0 ma ma active mode rx only peak current 11.9 ma ultra low power mode1 (note 2 ) standby doze 4.2 ua ultra low power mode2 (note 3 ) deep sleep (no ram retention) 750 na active mode average current (note 4 ) connection average current draw max with connection interval (min) 7.5 ms with connection interval 67.5 ms min with connection interval (max) 4000 ms ~400 ~2.6 - 4.1 ua ua note 1: if vcc is below 2.1v (operating range of dcdc ) , the peak current consumption will increase because the dcdc converter is switched off and the internal ldo is enabled . note 2 : standby doze is entered automatically (when waitevent statement is enc ountered within a smart basic application script). see individual peripherals current consumption in tables in section peripheral block current consumption 4.3 . note 3 : in deep sleep, everything is disabled and the only wake - up sources are reset and changes on pins on which sense is enabled. a reset is required to exit deep sleep. note 4 : data taken with tx power 3 dbm and all peripherals off (uart off after radio event) . average current consumption depends on a number of factors ( including tx power, vcc and accuracy of 16 mhz and 32.768 khz crystals ). with these factors fixed, the largest variable is the connection interval. connection interval range: 7.5 ms to 4000 ms in multiples of 1.25 ms. for a connection event: C the minimum average current consumption is when the connection interval is large 4000 ms C the maximum average current consumption is with the shortest connection interval of 7.5 ms; no slave latency. other factors that are also related to averag e current consumption include whether transmitting 6 packets per connection interval & each packet contains 20 bytes (which is the maximum for each packet) and an inaccurate 32 khz master clock accuracy would increase the average current consumption.
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 18 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 3.3.6.1 ble m easured peak current waveforms during connection figure 5 illustrate s ble current waveforms observed as the rm1xx module performs a transmit/receive cy cle with vcc = 3.3v . the plot was made using a shunt current sensor and the voltage waveform has been manually converted to current . the current represented is the total module current which is the sum of the ble_vcc and ble_lora pins. ble transmit/receive currents at vcc=3.3v @25?c figure 5 : typical peak current consumption profile with doze mode in effect before/after the rx/tx table 11 : ble peak transmit/receive currents vs vcc @25?c vcc [v] ble tx current [ma] ble rx current [ma] 3.5 12.0 11.4 3.3 12.7 11.9 3.0 13.3 12.3 2.7 14.4 13.0 1.8 16.6 15.02 note: this is the total module current (sum of pins vcc_ble and vcc_lora) 3.3.6.2 p eripheral block current consumption the values below are calculated f or a typical operating voltage of 3 v. table 12 : uart power consumption parameter min typ max unit uart run current @ max baud rate 2 3 0 ua uart run current @ 115200 bps 220 ua uart run current @ 1200 bps 210 ua uart baud rate 12 00 460800 bps
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 19 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 table 13 : spi power consumption parameter min typ max unit spi master run current @ 125 kbps 180 ua spi master run current @ 4 mbps 200 ua spi bit rate 0.125 4 mbps table 14 : i2c power consumption parameter min typ max unit i2c run current @ 100 kbps 380 ua i2c run current @ 400 kbps 400 ua i2c bit rate 100 400 kbps table 15 : adc power consumption parameter min typ max unit adc current during conversion 260 ua for asynchronous interface like the uart (asynchronous as the other end can communicate at any time), the uart (on rm1xx ) must kept open (by a command in smart basic application script) resulting in the base current consumption penalty. for synchronous interface like the i2c or spi (since rm1xx side is the master), the interface can be closed and opened only when needed (by a command in smart basic application script) , resulting in current saving (no base current cons umption penalty). theres a s imilar argument for adc (open adc when needed). 4 f unctional d escription the rm1xx module is a self - contained lora/ b luetooth l ow e nergy product and requires only power and a users smart basic application to implement full lora and ble functionality . the lora radio in conjunction with an external two dbi antenna implements a long range, low data rate connection to a lora gateway up to 15 kilometers . the integrated, high perfor mance ble antenna combined with the rf and b ase - band ci rcuitry provides the bluetooth low energy wireless link to connect to local ble sensors. the rm1xx sio lines provide the oems chosen interface connection to the wired serial/spi/i2c/analog sensors. the users smart basic application binds the sensors to th e lora and ble wireless functionality. the variety of hardware interfaces and the smart basic programming language allow the rm1xx module to serve a wide range of wired/wireless applications, whilst reducing overall time to market and the learning curve for developing lora and ble products. to provide the widest scope for integration , a vari ety of physical host interfaces/sensors are provided. the major rm1xx series module functional blocks are described below. 4.1 power management (includes brown - out and power on reset) power management features: ? system standby doze /deep sleep modes ? brownout reset
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 20 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 ? open/close p eripherals (uart, spi, i2c, sios and adc). peripherals consume current when open; each peripheral can be individually closed to save power consumption (wi th a command in a smart basic application script). ? two - region ram retention (no ra m retention in deep sleep mode) ? smart basic command allows the vcc voltage to be read (through the internal adc) ? pin wake - up system from deep sleep power supply features: ? supervisor hardware to manage power on reset, brownout (and power fail). ? 1.8v to 3.5v supply range. 4.2 clocks and timers 4.2.1 clocks the integrated high accuracy (+/ - 20 ppm) 32.768 khz crystal oscillator provides protocol timing and helps with r adio power consum p tion in the system standby doze /deep sleep modes by reducing the time that the rx window needs to be open. standard accuracy clocks tend to have lower accuracy +/ - 250 ppm. the integrated high accuracy 16 mhz (+/ - 10 ppm) crystal oscillator helps with r adio operation and also helps re duce power consumption in the ac tive modes. 4.2.2 timers in keeping with the event - driven paradigm of smart basic, the timer subsystem enables smart basic applications to be written which allow future events to be generated based on tim eouts. ? regular timer C there are eight built - in timers (regular timer s ) derived from a single rtc clock which are controlled solely by smart basic functions. the resolution of the regular timer is 976 microseconds. ? tick timer C a 31 - bit free running counte r that i ncrements every one millisecond. the resolution of this cou nter is 488 microseconds. this counter can be accessed using the functions gettickcount() and getticksince(). refer to the smart basic user guide for more information. 4.3 rf ? rm186 lora radio: 865 C 870 mhz (250 C 11000 bps over the air data rate) ? rm186 protocol can optionally employs 50 kbps fsk when enabled by the gateway ? rm191 lora radio: 902 C 928 mhz (980 C 21900 bps over the air data rate) ? bluetooth low energy radio: 2402 C 2480mhz (1 mbps over the air data rate). ? ble tx output power of +3 dbm programmable (via smart basic command) to - 20 dbm in steps of four db. ? ble tx whisper mode1 - 30 dbm (via smart basic command). ? ble tx whisper mode2 - 55 dbm (via smart basic command). ? ble receiver (with integrated channel filters) to achieve maximum sensitivity - 91 dbm @ 1 mbps ble. ? ble antenna: integrated monopole chip antenna on rm1xx 4.4 uart interface the universal asynchronous receiver/transmitter offers fast, full - duplex, asynchronous serial communication with built - in flow control support ( uart_ cts, uart_ rts) in the hardware . parity checking is supported.
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 21 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 uart_tx, uart_rx, uart_rts , and uart_cts form a conventional asynchronous serial data port with handshaking. the interface is design ed to operate correctly when connected to other uart devices such as the 16550a. the signaling levels are cmos logic levels that track vcc, and are inverted with respect to the signaling on an rs232 cable. two - way hardware flow control is implemented by uart_rts and uart_cts. uart_rts is an output and uart_cts is an input . both are active low. these signals operate according to normal industry convention. uart_rx, uart_tx, uart_cts, uart_rts are all cmos logic levels that track vcc . for example, wh en rx and tx are idle they sit a t a high logic level (vcc) . conversely for handshaking pins cts, rts a t 0 v is treated as an assertion. the module communicates with the customer application using the following signals ( figure 6 ) : ? port /txd of the application sends data to the modules uart_rx signal line ? port /rxd of the application receives data from the modules uart_tx signal line figure 6 : uart signals note: the rm1xx serial module output is at cmos logic levels that track vcc. level conversion must be added to interface to provide an rs - 232 level compliant interface. some serial implementations link cts and rts to remove t he need for handshaking. laird does not recommend linking cts and rts other than for testing and prototyping. if these pins are linked and the host sends data at the point that the rm1xx deasserts its rts signal, then there is significant risk that interna l receive buffers will overflow, which could lead to an internal processor crash. this will drop the connection and may require a power cycle to reset the module. laird recommends that the correct cts/rts handshaking protocol be adhered to for proper opera tion. table 16 : uart interface signal name pin # i/o comments sio_21 / uart_tx 2 o sio_21 (alternative function uart_tx) is an output, set high (in fw). sio_22/ uart_rx 3 i sio_22 (alternative function uart_rx) is an input, set with internal pull - up (in fw). sio_23/ uart_r ts 4 o sio_23 (alternative function uart_rts) is an output, set low (in fw). sio_24/ uart_c ts 5 i sio_24 (alternative function uart_cts) is an input, set with internal pull - down (in fw). the uart interface is also used to load customer developed smart basic application script. 4.5 spi bus the spi interface is an alternate function on sio pins, configurable by smart basic . the m odule is a master device that uses terminals spi_mosi, spi_miso, and spi_clk . spi_csb is implemented using any spare sio digital output pins to allow for multi - dropping.
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 22 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 the spi interface enables full duplex synchronous communication between devices. it supports a three - wire (spi_mosi, spi_miso, spi_sck,) bidirectional bus with fa st data transfers to and from multiple slaves. individual chip select signals are necessary for each of the slave devices attached to a bus, but control of these is left to the application through use of sio signals. i/o data is double buffered. the spi peripheral supports spi mode 0, 1, 2, and 3. table 17 : peripheral supports signal name pin # i/o comments spi_mosi 17 o this interface is an alternate function configurable by smart basic. default in the fw pin 1 5 and 1 7 are inputs. spiopen() in smart basic selects spi function and changes pin14 and 16 to outputs (when in spi master mode). spi_miso 16 i spi_clk 15 o 4.6 i2c interface the i2c interface is an alternate function on sio pins, configurable by smart basic command. the t wo - wire interface can interface a bi - directional wired - or bus with two lines (scl, sda) and has master /slave topology. the interface is capable of clock stretching. data rates of 100 kbps and 400 kbps are supported. an i2c interface a llows multiple masters and slaves to communicate over a shared wired - or type bus consisting two lines which normally sit at vcc. the rm1xx module can only be configured as an i2c master with additional constraint that it be the only master on the bus. the scl is the clock line which is always sourced by the master and sda is a bi - directional data line which can be d riven by any device on the bus. important: it is essential to remember that pull - up resistors on both scl and sda lines are not provided in th e module and must be provided external to the module. table 18 : i2c interface signal name pin # i/o comments i2c_sda 10 i/o this interface is an alternate function on each pin, configurable by smart basic. i2copen() in smart basic selects i2c function. i2c_scl 9 i /o 4.7 general purpose i/o, adc and pwm/freq 4.7.1 gpio all sio pins are configurable by smart basic . they can be accessed individually . e ach has the fol lowing user configured features: ? input/output direction ? output drive strength (standard drive 0.5 ma or high drive 5ma) ? internal pull up and pull down resistors (13 k typical) or no pull - up/down ? wake - up from high or low level triggers on all pins 4.7.2 adc the adc is an alternate function on four select sio pins, configurable by smart basic . this enables sampling up to four external s ignals via an internal mux to the 10 bit adc. the adc has configurable input pre - scaling and sample resolution.
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 23 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 4.7.2.1 analog interface (adc) table 19 : analog interface signal name pin no i /o comments ain C analog input 17 i this interface is an alternate function on each pin, configurable by smart basic . ain configuration selected using gpiosetfunc() function. 10 bit resolution. voltage scaling 1/1, 2/3, 1/3. ain C analog input 18 i ain C analog input 19 i ain C analog input 20 i 4.7.3 pwm and freq s ignal o utput on up to two sio pins the pwm and freq output is an alternate function on sio pins, configurable by smart basic. the ability to output a pwm (pulse width modulated) signal or freq output signal on up to two gpio (sio) output pins can be selected using gpiosetfunc() function. pwm output signal has a frequency and duty cycle property. pwm output is generated using 32 - b it hardware timers. the timers are clocked by a one - mhz clock source. frequency is adjustable (up to 1 mhz) and the duty cycle can be set over range from 0% to 100% (both configurable by smart basic command). note, the frequency driving each of the wo sio pins is the same but the duty cycle can be independently set for each pin. freq output signal frequency can be set over a range of 0 hz to 4 mhz (with 50% mark - space ratio). 4.8 nreset pin table 20 : nreset pin signal name pin no i/o comments nreset 22 i hw reset (active low ) . pull the nreset pin low for minimum 100ms in order for the rm1xx to reset. 4.9 nautorun pin refer to section nautorun pin and operating modes regarding operating modes and the nautorun pin. ? self - contained run mode ? interactive / development mode two - wire swd programming/debug interface you have the option of using the 2 - wire (s wd programming/debug) interface during production to clone the file system of a golden preconfigured rm1xx to others using the flash cloning process. contact laird support for details. signal name (hidden name) pin no i/o comments nreset (swdio) 22 i/o nc (swdclk) 23 i the connector for the (2 - wire swd programming/debug interface) mpn is as follows: reference part description jp1 n ote1 ftsh - 105 header, 1.27mm, smd, 10 - way, ftsh - 105 - 01 - l - dv samtec
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 24 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 note 1: reference the rm1xx development board schematic. figure 7 shows the wiring for the 2 - wire swd programming/debug interface connector and rm1xx module hidden 2 - wire swd programming/debug interface pins . figure 7 : wiring for 2 - wire swd programming/debug interface connector to swd programming/debug interface on rm1xx module 4.10 rm1xx on - board chip antenna characteristics the rm1xx on - board chip monopole antenna radiated performance depends on the host pcb layout. rm1xx development board was used for rm1xx development and antenna performance evaluation. to obtain similar performance follow guidelines in section pcb layout on host pcb for rm1xx to allow the on - board antenna to radiate and reduce proximity effects due to nearby host pcb gnd copper or metal covers. rm1xx on - board antenna part number: acx: at5020 - e3r0hban t/lf 5 h ardware i ntegration s uggestions 5.1 circuit the rm1xx - series module is easy to integrate requiring no external components on the customers board apart from those required by customer for development and in customers end application. checklist (for schematic): ? vcc the module vcc should be chosen to optimize either range or power consumption and must be within the valid operating range and noise/ripple specification of rm1xx . pins vcc_ble and vcc_lora should be tied together and d ecoupling capacitors for filtering sh ould be added close to the module vcc pins . the supply must be able to deliver enough current for the sum of the ble and lora transmitter currents for the chosen vcc (plus reasonable headroom). power - on reset circuitry within rm1xx series module incorpora tes brow n - out detector, thus simplifying power supply design. upon application of power, the internal power - on reset e nsures module starts correctly. ? ain (adc) and sio pin io voltage levels rm1xx sio operating voltage levels are from 0v to vcc. ensure inp ut voltage levels into sio do not exceed vcc also (if vcc source is a battery whose voltage will drop). ensure adc pin maximum inpu voltage for damage is not violated. ? ain ( adc ) impedance and external voltage divider setup if one wanted to measure with a dc, a voltage higher than 3.6v then one can connect a high impedance (rm1xx pin 22) (rm1xx pin 23 ) jp1 ftsh-105 1 2 3 4 5 6 7 8 9 10 swdclk vcc_io nreset/swdio gnd
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 25 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 voltage divider to lower the voltage to the adc input pin. other methods are to use a voltage buffer or fet transistor in conjunction with a low resistance voltage divider. high impedance values of a voltage divider connected to an ain pin will introduce adc inaccuracy. laird recommends the following solution for setup of a voltage divider when used with the rm1xx adc: C connect a capacitor between ain and ground (if the voltage divider pres ents high impedance). normally, when adc is not sampling, the adc (ain) impedance is a very high value and can be considered an open circuit. the moment adc is sampling, adc (ain) impedance is 200k - 600k and lowers the ain voltage . however, when the capacit or is connected it should keep the ain voltage at previous level for an adequate time period while sampling, minimizing the effect of the high resistance value of the external voltage divider. the capacitor should be big enough to hold voltage up for the r equired time period, i.e. 20 us for 8 bit sampling or 68 us for 10 bit sampling. if you use a fet transistor to open the current flow through the circuit momentarily before sampling, allow enough time for the capacitor to fully charge before sampling. duri ng the sampling period, multiple samples are made and the adc output value is the mean value from the sample pool. t he sample pool is created during 20 us period for 8 bit sampling, 36 us period for 9 bit sampling , and 68 bit period for 10 bit sampling. ? tw o - wire swd programming/debug interface r equired if flash cloning will be used during production to load rm1xx smart basic application and/or the firmware , add 2 - wire swd programming/debug interface as detailed in section 2 - wire swd programming/debug interface ? uart the uart is r equired for loading customer smart basic application and firmware . add connector to allow uart to be interfaced to pc (via uart C rs232 or uart - usb). ? uart_rx and uart_cts sio_22 (alternative functio n uart_rx) is an input, set with internal weak pull - up (in fw). the pull - up prevents the module from going into deep sleep when uart_rx line is idling. sio_24 (alternative function uart_cts) is an input, set with internal weak pull - down (in fw). this pull - down ensures the default state of the uart_cts will be asserted which means can send data out of the uart_tx line. in the case when uart_cts is not connected (which we do not recommend). ? nautorun pin and operating mode selection nautorun pin needs to be externally held high or low to select between the two rm1xx operating modes at power - up: C self - contained run mode (nautorun pin held at 0v). C interactive /development mode (nautorun pin held at vcc). ? make provision to allow o peration in the required mode. add jumper to allow nautorun pin to be held high or low (via 10k resistor) or driven by host gpio. ? i2c it is essential to remember that pull - up resistors on both i2c_ scl and i2c_ sda lines are not provided in the rm1xx module and must be provided external to the module as per i2c standard. ? spi implement spi chip select using any unused sio pin within your smart basi c application script then spi_cs is controlled from smart basi c application allowing multi - dropping. ? sio pin directi on rm1xx modules shipped from production with smart basic runtime engine fw , all sio pins (with default function of dio) are mostly digital inputs (see pin definitions table 2 ). use your smart basic application script to change the direction of any sio pin that is required to be an output in your design . also these sio pins that are inputs have by default (in fw) an internal pull - up or pull - down resistor - enabled (see pin
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 26 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 definitions table 2 ) . this was done to avoid floating inputs (which can also cause current cons umption in low power modes (e.g. standby doze) to drift with time. in any case customer can disable the pul l - up through their smart basic application. ? nreset pin (active low) hardware reset. wire out to push button or drive by host. by default module is o ut of reset when power applied to vcc pin . 5.2 pcb layout on host pcb C general checklist (for pcb): ? must locate rm1xx module close to the edge of pcb (mandatory for rm1xx for on - board chip antenna to radiate properly). ? use solid gnd plane on inner layer (for best emc and rf performance). ? all module gnd pins must be connected to host pcb gnd. ? place gnd vias close to module gnd pads as possible. ? unused pcb area on the top layer can be flooded with copper but place gnd vias regularly to connect copper flood to inner gnd plane. if gnd flood copper exists on the top pcb layer (under of the rm1xx module), then connect with gnd vias to inner gnd plane and ensure that it is covered with solder mask. ? route traces to avoid noise being picked up on vcc supply and ain (analogue) and sio (digital) traces. ? ensure no exposed copper beneath the module (refer to land pattern of rm1xx development board). 5.2.1 ble chip antenna keep - out on h ost pcb ? ensure there is no copper in the antenna keep - out area on any layers of the host pcb. keep all mounting hardware and metal clear of the area to allow proper antenna radiation. ? for best antenna performance, place the rm1xx module on the edge of the host pcb, preferably in the corner with the antenna facing the corner. ? the rm1xx developm ent board has the rm1xx module on the edge of the board (not in the corner). the antenna keep - out area is defined by the rm1xx development board which was used for module development ( and antenna performance evaluation ) is shown in figure 8 , where the antenna keep - out area is composed of pcb dielectric (no copper) sitting under the rm1xx antenna. ? a different host pcb thickness dielectric will have smal l effect on antenna. ? the antenna - keep - out defined in host pcb land pattern and antenna keepout applies when the rm1xx is placed in the corner of the host pcb. when rm1xx - sm cannot be placed as such, it must be placed on th e edge of the host pcb and the antenna keep out must be observed. an example is shown in figure 8 .
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 27 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 figure 8 : antenna keepout on dvk - rm1xx pcb (shown in red) with rm1xx module placed near the corner . note: 1. rm1xx module placed on edge of host pcb (close to the corner of the pcb) . 2. copper cut - away on all layers in antenna keep - out for a host pcb. 5.2.2 antenna k eep - out and proximity to metal or plastic checklist (for metal /plastic enclosure): ? minimum safe distance for metals without seriously compromising the an tenna (tuning) is 40mm top/bottom and 30mm left or right. ? metal close to the rm1xx chip monopole antenna (bottom, top, left, right, any direction) will have degradation on the antenna performance. how much; that is entirely system dependent which means som e testing by customer required (in their host application). ? anything metal closer than 20mm will start to significantly degrade performance (s11, gain, radiation efficiency). ? it is best that the customer tests the range with mock - up (or actual prototype) of the product to assess effects of enclosure height (and material whether metal or plastic).
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 28 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 5.3 lora external antenna integration with rm1xx please refer to the regulatory sections for fcc / ic , and ce , for details of use of rm1xx with external antennas. the rm1xx has been designed to operate with the below external antennas (with a maximum gain of 2dbi). the required antenna impedance is 50 ohms. see table 21 . table 21 : lora external antennas for the rm1xx external antenna part number laird part number mfg. type gain (dbi) connec tor type rm1xx part number rfdpa131015imbb301 0600 - 00060 walsin dipole 0 .9 u.fl rm191/rm186 wpantdp036 - r5a - world products dipole 2. 0 u.fl rm191/rm186 s152cl - l - px - 915s - nearson dipole 2.0 u.fl rm191 s152cl - l - px - 868s - nearson dipole 2.0 u.fl rm186 6 m echanical d etails 6.1 rm1xx mechanical details figure 9 : rm1xx mechanical drawings development kit schematics can be found in the documentation tab of the rm1xx product page: www.lairdtech.com/products/rm1xx - lora - modules
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 29 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 6.2 host pcb land pattern and anten na keep - out for rm1xx application notes 1 . ensure there is no copper in the antenna keep out area on any layers of the host pcb. also keep all mounting hardware or any metal clear (refer to 5.2.2 ) on of the area to reduce effects of proximity detuning the antenna and to help antenna radiate properly. 3. for best ble chip antenna performance, the module must be placed on the edge of t he host pcb ( preferably in the corner ) with the antenna facing the corner. if rm1xx is not placed in corner , but on edge of host pcb, the antenna keep out area is extended (see note 4). 4. rm1xx development board has an rm1xx placed on the edge of the pc b board (and not in corner) the antenna keep out area is extended out to the corner of the development board, see section pcb layout on host pcb - general . this was used for module development and antenna performance evaluation. 5. ensure no exposed copper under module on host pcb. 6. the user may modify the pcb land pattern dimensions based on their experience and / or process capability.
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 30 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 7 a pplication n ote for s urface m ount m odules 7.1 introduction laird technologies sur face mount modules are designed to conform to all major manufacturing guidelines. this application note is intended to provide additional guidance beyond the information that is presented in the user manual. this application note is considered a living doc ument and will be updated as new information is presented. the modules are designed to meet the needs of a number of commercial and industrial applications . they are easy to manufacture and conform to current automated manufacturing processes. shipping figure 10 : rm1xx shipping tray details modules are shipped in esd (electrostatic discharge) safe trays that can be loaded into most manufacturers pick and place machines. layouts of the trays are provided in figure 10 .
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 31 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 7.2 reflow parameters prior to any reflow, it is important to ensure the modules were packaged to prevent moisture absorption. new packages contain desiccate (to absorb moisture) and a humidity indicator card to display the level maintained during storage and shipment. if directed to bake units on the card, see table 22 and follow instructions specified by ipc/jedec j - std - 033. a copy of this standard is available from the jedec website: http://www.jede c.org/sites/default/files/docs/jstd033b01.pdf note: the shipping tray cannot be heated above 65c. if baking is required at the higher temperatures displayed in in table 22 , the modules must be removed from the shipping tray. any modules not manufactured before exceeding their floor life should be re - packaged with fresh desiccate and a new humidity indicator card. floor life for msl (moisture sensitivity level) 3 devices is 168 hours in ambient environment ? 30c/60%rh. table 22 : recommended baking times and temperatures msl 125 c baking temp. 90 c/ 5%rh baking temp. 40 c/ 5%rh baking temp. saturated @ 30 c/85% floor life limit + 72 hours @ 30 c/60% saturated @ 30 c/85% floor life limit + 72 ho urs @ 30 c/60% saturated @ 30 c/85% floor life limit + 72 hours @ 30 c/60% 3 9 hours 7 hours 33 hours 23 hours 13 days 9 days laird surface mount modules are designed to be easily manufactured, including reflow soldering to a pcb. ultimately it is the responsibility of the cust o mer to choose the appropriate solder paste and to ensure oven temperatures during reflow meet the requirements of the solder paste. laird surface mount modules conform to j - std - 020d1 standards for reflow temperatures. important: during reflow, modules should not be above 260 and not for more than 30 seconds. figure 11 : recommended reflow temperature
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 32 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 temperatures should not exceed the minimums or maximums presented in table 23 . table 23 : recommended maximum and minimum temperatures specification value unit temperature inc./dec. rate (max) 1~3 c / sec temperature decrease rate (goal) 2 - 4 c / sec soak temp increase rate (goal) .5 - 1 c / sec flux soak period (min) 70 sec flux soak period (max) 120 sec flux soak temp (min) 150 c flux soak temp (max) 190 c time above liquidous (max) 70 sec time above liquidous (min) 50 sec time in target reflow range (goal) 30 sec time at absolute peak (max) 5 sec liquidous temperature (sac305) 218 c lower target reflow temperature 240 c upper target reflow temperature 250 c absolute peak temperature 260 c 8 fcc and ic r egulatory s tatements model us/fcc canada/ic rm191 - sm sqg - rm191 3147a - rm191 the oem must follow the regulatory guidelines and warnings listed below to inherit laird modular approval. the rm191 - sm holds full modular approvals and has been certified for integration to products only by oem integrators under the following conditions: 1. the antenna(s) must be installed such that a minimum separation distance of 30mm is maintained between the radiator (antenna) and all persons at all times. 2. the transmitter modu le must not be operating in conjunction with any other antenna or transmitter, except in accordance with fcc multi - transmitter product procedures. as long as the two conditions above are met, further transmitter testing will not be required. however, the o em integrator is still responsible for testing their end - product for any additional compliance requirements required with this module installed (for example, digital device emissions, pc peripheral requirements, etc.). important note: in the event that the se conditions cannot be met (for certain configurations or co - location with another transmitter), then the fcc and industry canada authorizations are no longer considered valid and the fcc id and ic certification number cannot be used on the final product. in these circumstances, the oem integrator will be responsible for re - evaluating the end product (including the transmitter) and obtaining a separate fcc and industry canada authorization.
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 33 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 the rm191 - sm lora transmitter h as been designed and approved to op erate with the antennas listed below with a maximum gain of 2 dbi. the required antenna impedance is 50 ohms. external antenna part number laird part number mfg. type gain (dbi) connector type rm1xx part number rfdpa131015imbb301 0600 - 00060 walsin dipole 0 .9 u.fl rm191 - sm wpantdp036 - r5a - world products dipole 2. 0 u.fl rm191 - sm s152cl - l - px - 915s - nearson dipole 2.0 u.fl rm191 - sm note: for the lora (external) dipole antenna, t he oem is free to choose another vendors antenna of like type and equal or lesser gain (2dbi) and still maintain compliance. reference fcc part 15.204(c)(4) for further information on this topic. the rm191 ble transmitter contains an on - board 2.4ghz chip antenna item part number mfg. type gain (dbi) rm1xx part number 1 at5020 - e3r0hbant/lf acx ceramic - 1.5 rm191 - sm 8.1 power exposure information federal communication commission (fcc) radiation exposure statement: to comply with fcc rf exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 3 0 m m from all persons and operating in conjunction with any other antenna or transmitter. oem responsibilities warning : the oem must ensure that fcc and industry canada labelling requirements are met. this includes a clearly visible label on the outside of the oem enclosure specifying the appropriate laird fc c identifie r for this product. contains fcc id: sqg - rm191 contains ic: 3147a - rm191 the oem of the rm191 - sm module must only use the approved antenna(s) listed above, which have been certified with this module. the oem integrator has to be aware not to provide in formation to the end user regarding how to install or remove this rf module or change rf related parameters in the user manual of the end product. the user manual for the end product must also include the following information in a prominent location: to comply with fcc and industry canada rf exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 30 mm from all persons and operating in conjunc tion with any other antenna or transmitter, except in accordance with fcc multi - transmitter product procedures. if the size of the end product is larger than 8x10cm, then the following fcc part 15.19 statement has to also be available on visible on outside of device:
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 34 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 the enclosed device complies with part 15 of the fcc rules. operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interfer ence that may cause undesired operation label and text information should be in a size of type large enough to be readily legible, consistent with the dimensions of the equipment and the label. however, the type size for the text is not required to be lar ger than eight point. caution : the oem should have their device which incorporates the rm191 - sm tested by a qualified test house to verify compliance with fcc part 15 subpart b limits for unintentional radiators. warning : c hanges or modifications not expressly approved by laird could void the users authority to operate the equipment. fcc interference statement this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to pa rt 15 of the fcc rules. these limits are designed to provide reasonable protection against harmful interference in a residential installation. this equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordan ce with the instructions, may cause harmful interference to radio communications. however, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television recepti on, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one or more of the following measures: ? re - orient or relocate the receiving antenna ? increase the separation between the equipment and th e receiver ? connect the equipment to an outlet on a circuit different from that to which the receiver is connected. ? consult the dealer or an experienced radio/tv technician for help. fcc warning: this device complies with part 15 of the fcc rules operat ion is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. industry canada (ic) warning: this dev ice complies with industry canada license - exempt rss standard(s). operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause unde sired operation of the device. french equivalent is: le prsent appareil est conforme aux cnr d'industrie canada applicable aux appareils radio exempts de licence. l'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas prod uire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 35 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 ic radiation exposure statement to comply with industry canada rf exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 30mm from all persons and must not be operating in conjunction with any other antenna or transmi tter. remarque importante dclaration ic d'exposition aux radiations pour se conformer industrie canada rf limites d'exposition pour la population gnrale / exposition non contr?le, l'antenne utilise pour ce transmetteur doit tre installe pour fournir une distance d'au moins 30 mm de toutes les personnes et ne doit pas fonctionner en conjonction avec toute autre antenne ou transmetteur. modular approval oem integrator is still responsible for testing their end product for any additional complian ce requirements required with this module installed (for example, digital device emissions, pc peripheral requirements, etc.). approbation modulaire oem intgrateur est toujours responsable de tester leur produit final pour les exigences de conformit supp lmentaires ncessaires ce module install (par exemple, les missions de priphriques numriques, les exigences de priphriques pc, etc.) important note: in the event that these conditions cannot be met (for example certain laptop configurations or co - location with another transmitter), then the canada authorization is no longer considered valid and the ic id cannot be used on the final product. in these circumstances, the oem integrator will be responsible for re - evaluating the end product (includin g the transmitter) and obtaining a separate canada authorization. note importante: dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co - localisation avec un autre met teur), l'autorisation du canada n'est plus considr comme valide et l'id ic ne peut pas tre utilis sur le produit final. dans ces circonstances, l'intgrateur oem sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une auto risation distincte au canada. le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: " rm191 - sm contient des ic: 3147a - rm191"; 9 ce r egulatory the rm186 has been tested for compliance with relevant standards for the eu mark et. the rm186 module has been tested with a 2.0dbi external dipole antenna for lora, and the - 1.5dbi on - board chip antenna for the ble transmitter. for the external lora dipole antenna, the oem can operate any other type of antenna but must ensure that the gain does not exceed 2.0dbi to maintain the laird technologies approval. the oem should consult with a qualified test house before entering their device into an eu member country to make sure all regulatory requirements have been met for their complete de vice. reference the declaration of conformities listed below for a full list of the standards that the modules were tested to. test reports are available upon request.
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 36 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 9.1 antenna information the external flying lead u.fl dipole antennas for the 868mhz lora r adio listed below were tested for use with the rm186. for ce mark countries, the oem is free to use any manufacturers antenna and type of antenna as long as the gain is less than or equal to the highest gain approved for use (2.0dbi ) contact a laird techn ologies representative for more information regarding adding antennas. item lora antenna part# artnumber laird part number mfg. type gain (dbi) 1 rfdpa131015imbb301 0600 - 00060 walsin dipole 0.9 2 wpantdp036 - r5a world products dipole 2.0 3 s152cl - l - px - 868s nearson dipole 2. 0 the ble transmitter on board the rm186 has been approved with an on - board - 1.5dbi chip antenna item part number mfg. type gain (dbi) rm1xx part number 1 at5020 - e3r0hbant/lf acx ceramic - 1.5 rm191 - sm note: the rm186 module internal ble chipset ic pins are rated 4 kv (esd hbm). esd can find i ts way through the external 2 - wire swd programming/debug interface connector (if used on the customers design), if discharge is applied directly. customer should ensure adequ ate protection against esd on their end product design (using the rm186 module) to meet relevant esd standard (for ce, this is en301 - 489).
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 37 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 10 eu d eclarations of c onformity 10.1 rm186 - sm manufacturer: laird product: rm186 - sm eu directive: rtte 1995/5/ec conformity assessment: annex iv reference standards used for presumption of conformity: ar ticle number requirement reference standard(s) 3.1a health and safety en60950 - 1:2006+a 2:2013 3.1b protection requirements with respect to electromagnetic compatibility en 301 489 - 1 v1.9.2 (2011 - 09) en 301 489 - 3 v1.6.1 (2013 - 08) en 301 489 - 17 v2.2.1 (2012 - 09) emissions: en55022:2006/a1:2007 (class b) immunity: en61000 - 4 - 2:2009 en61000 - 4 - 3:2006/a1:2008/a2:2010 3.2 means of the efficient use of the radio freq uency spectrum en 300 220 - 2 v2.4.1 (2012 - 05) en 300 328 v1. 9 .1 (201 5 - 0 2 ) declaration: we, laird, declare under our sole responsibility that the essential radio test suites have been carried out and that the above product to which this declaration relates is in conformity with all the applicable essential requirements of article 3 of the eu directive 1999/5/ec, when used for its intended purpose. place of issue: laird w66n220 commerce court, cedarburg, wi 53012 usa tel: +1 - 262 - 375 - 4400 fax: +1 - 262 - 364 - 2649 date of issue: april 2016 name of authorized person: thomas t smith , director of emc compliance
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 38 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 11 o rdering i nformation part number description rm186 - sm intelligent lora/ble module [868mhz lora for europe] featuring smart basic rm191 - sm intelligent lora/ble module [915mhz lora for us] featuring smart basic dvk C rm186 - sm development board with rm186 - sm module soldered in place dvk C rm191 - sm development board with rm191 - sm module soldered in place 11.1 general comments this is a preliminary datasheet. please check with laird for the latest information before commencing a design. if in doubt, ask. 12 b luetooth sig q ualification 12.1 overview the rm186 and rm191 modules are listed on the bluetooth sig website as qualified end products. design name own er declaration id link to listing on the sig website rm186 - sm laird d030952 https://www.bluetooth.org/tpg/qli_viewqdl.cfm?qid=30952 rm191 - sm laird d030952 https://www.bluetooth.org/tpg/qli_viewqdl.cfm?qid=30952 it is a mandatory requirement of the bluetooth special interest group (sig) that every product implementing bluetooth technology has a declaration id. every bluetooth design is required to go through the qualification process, even when referencing a bluet ooth design that already has its own declaration id. the qualification process requires each company to register as a member of the bluetooth sig C www.bluetooth.org the following is a link to the bluetooth regis tration page: https://www.bluetooth.org/login/register/ for each bluetooth design it is necessary to purchase a declaration id. this can be done before starting the new qualification, either thr ough invoicing or credit card payment. the fees for the declaration id will depend on your membership status, please refer to the following webpage: https://www. bluetooth.org/en - us/test - qualification/qualification - overview/fees for a detailed procedure of how to obtain a new declaration id for your design, please refer to the following sig document, (login is required to views this document): https://www.bluetooth.org/docman/handlers/downloaddoc.ashx?doc_id=283698&vid=317486 qualification s teps w he n r eferencing a laird end product design to quali fy your product when referencing a laird end - product design, follow these steps: 1. to start a listing, go to: https://www.bluetooth.org/tpg/qli_sdoc.cfm note: a user name and password are required to access this site. 2. in step 1, select the option, new listing and reference a qualified design. 3. enter d030952 in the end product table entry. 4. select your pre - paid declaration id from the drop down menu or go to the purchase declaration id page.
lora/ble modules datasheet embedded wireless solutions support center: http://ews - support.lairdtech.com www.lairdtech.com/wireless 39 ? copyright 2016 laird. all rights reserved americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 2923 0610 note: unless the declaration id is pre - paid or purchased with a credit card, you cannot proceed until the sig invoice is paid. 5. once all the relevant sections of step 1 are finished, complete steps 2, 3, and 4 as described in t he help document accessible from the site. your new design will be listed on the sig website and you can print your certificate and sdoc. for further information please refer to the following training material: https://www.bluetooth.org/en - us/test - qualification/qualification - overview/listing - process - updates note: if using the rm1xx with laird firmware and smart basic script, you can skip contro ller subsystem, host subsystem, and profile subsystem . 12.2 additional assistance please contact your local sales representative or our support team for further assistance: laird technologies connectivity products business unit support centre: http://ews - support.lairdtech.com email: wireless.support@lairdtech.com phone: americas: +1 - 800 - 492 - 2320 europe: +44 - 1628 - 858 - 940 hong kong: +852 292 3 0610 web: http://www.lairdtech.com/bluetooth ? copyright 2016 laird. all rights reserved. patent pending. any information furnished by laird and its agents is believed to be accurate and reliable. all specifications are subject to change without notice. responsibility for the use and application of laird materials or product s rests with the end user since laird and its agents cannot be aware of all potential uses. laird makes no warranties as to non - in fringement nor as to the fitness, merchantability, or sustainability of any laird materials or products for any specific or general uses. laird, laird technologies, inc., or any o f its affiliates or agents shall not be liable for incidental or consequentia l damages of any kind. all laird products are sold pursuant to the laird terms and conditions of sale in effect from time to time, a copy of which will be furnished upon request. when used as a tradename herein, laird means laird plc or one or more subsidi aries of laird plc. laird?, laird technologies?, corresponding logos, and other marks are trademarks or registered trademarks of laird. othe r marks may be the property of third parties. nothing herein provides a license under any laird or any third party i ntellectual property right.

▲Up To Search▲

Price & Availability of RM186-SM

	To Download RM186-SM Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .